manualshive.com logo in svg

Dodge 2011 Challenger, Owner'S Manual

The Dodge 2011 Challenger is a powerhouse of a vehicle, providing an exhilarating driving experience. To ensure you get the most out of your Challenger, make sure to download the free user manual from manualshive.com. This manual offers detailed specifications and instructions to help you fully enjoy this iconic car.

Share
Download
background image

CAUTION!

•

If the transmission is not operative then the only
approved method of towing is with a flatbed
truck. Otherwise, damage to the transmission may
result.

•

Exceeding these towing limits may cause severe
transmission damage. Such damage is not covered
by the New Vehicle Limited Warranty.

If you must use the accessories (wipers, defrosters, etc.)
while being towed, the ignition must be in the RUN
position, not the ACC position. Make certain the trans-
mission remains in NEUTRAL.

CAUTION!

•

Do not attempt to tow this vehicle from the front
with sling-type towing equipment. Damage to the
front fascia will result.

•

Do not tow the vehicle from the rear. Damage to
the rear sheet metal and fascia will occur.

•

Do not push or tow this vehicle with another
vehicle as damage to the bumper fascia and trans-
mission may result.

Towing This Vehicle Behind Another Vehicle With
A Tow Dolly

The manufacturer

does not recommend

that you tow this

vehicle on a tow dolly. Vehicle damage may occur.

6

WHAT TO DO IN EMERGENCIES

379

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Qube AP1 Supplemental Instructions preview
AP1
Brand: Qube Pages: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Brand: Cadillac Pages: 32
HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Brand: Jeep Pages: 108
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
Kuda-Phonebase 055040 Installation Instruction preview
055040
Brand: Kuda-Phonebase Pages: 3
Veigel S47290920 Installation And Operating Instructions Manual preview
S47290920
Brand: Veigel Pages: 24
Cellular Line interphone Instruction Manual preview
interphone
Brand: Cellular Line Pages: 25
Cadillac 1993 Seville Owners Literature preview
1993 Seville
Brand: Cadillac Pages: 407
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
Kargo Master 8006A Instruction Manual preview
8006A
Brand: Kargo Master Pages: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Brand: Safe Fleet Pages: 12
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
ConWys AG 21500598C VW Fitting Instructions Manual preview
21500598C VW
Brand: ConWys AG Pages: 16
Volvo 1989 780 Owner'S Manual preview
1989 780
Brand: Volvo Pages: 123

Brands by name

Popular brands

Load more brands