Dodge 2011 Challenger Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 490

background image

To Lock The Doors

Press and release the LOCK button on the RKE transmit-
ter to lock both doors. The turn signal lights will flash
and the horn will chirp to acknowledge the signal.

Refer to “Keyless Enter-N-Go” under “Things To Know
Before Starting Your Vehicle” for further information.

Sound Horn With Remote Key Lock

This feature will cause the horn to chirp when the doors
are locked with the RKE transmitter or the Passive Entry
feature. This feature can be turned on or turned off. Refer
to “Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable Features)” in
“Understanding Your Instrument Panel” for further in-
formation.

•

When not using the EVIC, perform the following
steps:

1. Press the LOCK button on a programmed RKE trans-
mitter for at least 4 seconds, but no longer than 10 sec-
onds. Then, press the PANIC button while still holding
the LOCK button.

2. Release both buttons at the same time.

3. Test the feature while outside of the vehicle by pressing
the LOCK button on the RKE transmitter with the ignition
switch in the OFF position and the Key Fob removed.

4. Repeat these steps if you want to return this feature to
its previous setting.

NOTE:

Pressing the LOCK button on the RKE transmit-

ter while you are in the vehicle will activate the Security
Alarm. Opening a door with the Security Alarm activated
will cause the alarm to sound. Press the UNLOCK button
to deactivate the Security Alarm.

24

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
24
25
26
27
28
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Brand: U.S. General Pages: 5

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Yakima Pages: 4

Brand: Audi Pages: 12

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Rugged Ridge Pages: 3

Brand: ULTIMATE SPEED Pages: 40

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: Lincoln Pages: 586

CERTA CTCVINCVR14A

Brand: Kogan Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands