Dodge 2011 Challenger Owner'S Manual Download Page 262 | Manualshive

Page: 262 / 490

background image

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.

WARNING!

Remember to disconnect the engine block heater
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution.

MANUAL TRANSMISSION — IF EQUIPPED

Six-Speed Manual Transmission

WARNING!

You or others could be injured if you leave the
vehicle unattended without having the parking
brake fully applied. The parking brake should al-
ways be applied when the driver is not in the vehicle,
especially on an incline.

CAUTION!

•

Never drive with your foot resting on the clutch
pedal, or try to hold the vehicle on a hill with the
clutch pedal partially engaged, as this will cause
abnormal wear on the clutch. Refer to “Electronic
Brake Control System/Hill Start Assist” in “Start-
ing and Operating” for further information.

•

Failure to press the clutch pedal fully to the floor
may cause increased shift efforts, and may result
in damage to the clutch and transmission.

•

Do not rest your hand on the shift lever while
driving, as this may result in transmission syn-
chronizer damage.

•

Do not attempt to shift the transmission if the rear
wheels are spinning due to loss of traction. Dam-
age to the transmission may occur.

260

STARTING AND OPERATING

«
...
260
261
262
263
264
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Brand: Acdeos Pages: 38

Brand: Warrior Winches Pages: 17

Brand: Metra Electronics Pages: 2

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Phonocar Pages: 2

Brand: Oldsmobile Pages: 2

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: GMC Pages: 430

Brand: iArmor Pages: 6

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: A-Tach Mounts Pages: 2

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brand: Axxess Pages: 8

Brand: Subaru Pages: 16

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brand: Lance Pages: 132

Brand: Thule Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands