Dodge 2011 Challenger Owner'S Manual Download Page 186 | Manualshive

Page: 186 / 490

background image

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the brake light on is danger-
ous. Part of the brake system may have failed. It will
take longer to stop the vehicle. You could have a
collision. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System
(ABS), are also equipped with Electronic Brake Force
Distribution (EBD). In the event of an EBD failure, the
Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by
turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.

The light also will turn on when the parking brake is
applied with the ignition switch in the ON/RUN posi-
tion.

NOTE:

This light shows only that the parking brake is

applied. It does not show the degree of brake application.

184

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
184
185
186
187
188
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

AUDI 4G HIGHEND

Brand: KAP Pages: 20

Brand: Kathrein Pages: 7

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: FormFit Pages: 2

Brand: PullRite Pages: 10

Brand: iArmor Pages: 4

Brand: EZTRUNK Pages: 3

Brand: Honda Pages: 85

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: Brodit Pages: 2

Brand: CrimeStopper Pages: 1

Brand: DFI Pages: 6

Brand: POOL-LINE Pages: 2

Brand: Ferve Pages: 28

PRIME DESIGN VRR3-FT21G-ST

Brand: Safe Fleet Pages: 12

2013 2500 Big Horn

Brand: RAM Pages: 12

Brand: EUFAB Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands