Dodge 2011 Challenger Owner'S Manual Download Page 432

Page: 432 / 490

6. Pull the tail lamp assembly clear from the vehicle to
access the bulbs.

7. Push the electrical connector locking tab to the side.

8. Disconnect the electrical connector.

9. Turn the appropriate bulb and socket assembly coun-
terclockwise to remove it from the tail lamp assembly.

10. Disconnect the bulb from the socket assembly and
install the replacement bulb.

11. Reinstall the bulb and socket assembly into the tail
lamp assembly, and then turn it clockwise.

12. Reinstall the tail lamp assembly, fasteners, electrical
connector, and trunk liner.

13. Reinstall tail lamp retainer.

430

MAINTAINING YOUR VEHICLE

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Search results

Summary of Contents for 2011 Challenger

Reviews:

Related manuals for 2011 Challenger

Brands by name

Popular brands

Dodge 2011 Challenger, Owner'S Manual

Search results

Summary of Contents for 2011 Challenger

Reviews:

Related manuals for 2011 Challenger

Brands by name

Popular brands