Dodge 2011 Challenger Owner'S Manual Download Page 92 | Manualshive

Page: 92 / 490

background image

Automatic Dimming Mirror — If Equipped

This mirror automatically adjusts for headlight glare
from vehicles behind you. You can turn the feature on or
off by pressing the button at the base of the mirror. A light
to the left of the button will illuminate to indicate when
the dimming feature is activated. The sensor to the right
of the button does not illuminate.

CAUTION!

To avoid damage to the mirror during cleaning, never
spray any cleaning solution directly onto the mirror.
Apply the solution onto a clean cloth and wipe the
mirror clean.

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s)
to center on the adjacent lane of traffic and a slight
overlap of the view obtained from the inside mirror.

NOTE:

The passenger side convex outside mirror will

give a much wider view to the rear, and especially of the
lane next to your vehicle.

Automatic Dimming Mirror

90

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
90
91
92
93
94
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

Brand: Chariot Carriers Pages: 3

Green Motion DC 66

Brand: Eaton Pages: 18

Brand: Cadillac Pages: 20

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: cam Pages: 28

Brand: Cadillac Pages: 2

Brand: Buick Pages: 20

Brand: BMW Pages: 392

Brand: Curt Manufacturing Pages: 4

Brand: Saab Pages: 37

Brand: Gentex Pages: 2

1995 C/K Pickup

Brand: Chevrolet Pages: 483

Brand: HOLDEN Pages: 330

Brand: Audiovox Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands