manualshive.com logo in svg

Dodge 2011 Challenger, Owner'S Manual

The Dodge 2011 Challenger is a powerhouse of a vehicle, providing an exhilarating driving experience. To ensure you get the most out of your Challenger, make sure to download the free user manual from manualshive.com. This manual offers detailed specifications and instructions to help you fully enjoy this iconic car.

Share
Download
background image

WARNING!

The air induction system (air cleaner, hoses, etc.) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc.) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the
vehicle with the air induction system (air cleaner,
hoses, etc.) removed. Failure to do so can result in
serious personal injury.

Engine Air Cleaner Filter Selection

The quality of replacement engine air cleaner filters
varies considerably. Only high quality filters should be
used to assure most efficient service. MOPAR

威

engine air

cleaner filters are a high quality filter and are
recommended.

Maintenance-Free Battery

Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic main-
tenance required.

NOTE:

The battery is stored under an access cover in

the trunk. Remote battery terminals are located in the
engine compartment for jump-starting. Refer to “Jump-
Starting Procedures” in “What To Do In Emergencies” for
further information.

394

MAINTAINING YOUR VEHICLE

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Happy Orange USB-C Quick Start Manual preview
USB-C
Brand: Happy Orange Pages: 2
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Brand: hager Pages: 9
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Brand: RAM Commercial Pages: 12
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Brand: Lincoln Pages: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Brand: Volkswagen Pages: 26
TATA Motors Indigo MANZA QUADRAJET 90 Owner'S Manual & Service Book preview
Indigo MANZA QUADRAJET 90
Brand: TATA Motors Pages: 10
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Brand: U.S. General Pages: 8
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
GReddy 12519101 Instruction Manual preview
12519101
Brand: GReddy Pages: 12
SSV Works RG4-DM3 Manual preview
RG4-DM3
Brand: SSV Works Pages: 2
Westin 28-21030 Instructions preview
28-21030
Brand: Westin Pages: 3
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Brand: T.J.M. Pages: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Brand: Audi Pages: 4
Tobe EPS-LD SafePark Technical Data preview
EPS-LD SafePark
Brand: Tobe Pages: 2
Baby Jogger CITY GO PD349056A Assembly Instructions Manual preview
CITY GO PD349056A
Brand: Baby Jogger Pages: 16
Saab 12 832 509 Installation Instructions Manual preview
12 832 509
Brand: Saab Pages: 11

Brands by name

Popular brands

Load more brands