background image

1838-066-E-12-16

8

1.4 16.5 VAC Power Wiring ONLY!

The 1838 operates 

ONLY

 on 16.5 VAC. 

DO NOT power the unit with 24 volt AC power.

 Use the supplied power transformer, 16 

VAC, 20 VA (or U.L. listed equivalent) to power the system. 

DO NOT power any other devices (electric strikes, magnetic 

locks, etc.) from the unit’s power transformer.

 See table below for wire run distances.

Power Interruption Note:

 The Time 

and Date calendar chip (Section 2, 
2.7.1) in the 1838 will keep time for 
approximately 48 hours if power to 
the system is lost or removed. If 
power is off 

longer

 than this, 

the 

Time and Date will need to be 
reprogrammed into the system.

 All 

other specific programming that has 
been done will remain intact after 
power has been restored.

DoorKing offers a 

12 volt .8 amp

 

hour gel cell battery

 that can 

connect to the main terminals 9 and 
10 to provide back-up power during 
power interruptions.
(DoorKing P/N 1801-008)

Over Voltage Power Note:

 LED located on 

bottom left corner of board will light up if 
too much power is applied to circuit board.

Wire Size

Max Distance

18 AWG

16 AWG

100 ft

200 ft

Power Transformer Wire Run Table

1.5 Grounding and Surge Suppression

Power Transformer Wires

(Not supplied)

Supplied Transformer

Polarity does 
not matter.

Output

16.5 V

AC

20 V

A

CAUTION

DO NOT 

power the unit from a 24-Volt 

source (Such as a gate operator).

Damage will occur to the unit 

that is 

NOT 

covered under DoorKing’s warranty.

Proper Grounding and the use of surge suppressors can significantly reduce the chance of component failure because of static 
charges or surges. To be effective, ground connections should be made with a minimum 12 AWG wire to a ground point within 
10 feet of the device being protected. The ground point can be at an electrical panel, a metallic cold water pipe that runs in the 
earth or a grounding rod driven at least 10 feet into the soil. 

A gooseneck mounting post anchored in concrete does NOT make 

a good ground.

Telephone Line Surge Suppressor

It is highly recommended that telephone line surge 
suppressor (DoorKing P/N 1877-010) be installed 
to help protect the system from phone line power 
surges. Surge suppressor must be positioned 3 ft 
or less from the ground source, 12 AWG min.

Low Voltage Surge Suppressor

It is highly recommended that a low voltage surge 
suppressor (DoorKing P/N 1878-010) be installed to 
help protect the telephone entry system from power 
surges. Surge suppressor must be positioned 3 ft or 
less from the ground source, 12 AWG min.

Some Acceptable Ground Sources

Ground to metallic cold water pipe.

Ground

Wire

Ground

Wire

Phone Company

Transformer

Ground to existing electrical system.

Electrical

Panel

Grounding rod 10 feet in soil.

IMPORTANT:

 Ground wire shown without 

safety protection for clarity. Make sure 
ground wire is protected from being 
touched or electrical shock could occur!

Surge suppressor within
3 ft of ground source.

PHONE LINE

1877-010

Surge suppressor

within 10 ft of unit.

Surge suppressor within
3 ft of ground source.

POWER LINE

1878-010

Surge suppressor

within 10 ft of unit.

OV

Summary of Contents for 1838 Access Plus









































Reviews: