1838-066-E-12-16
23
2.4.7 Relay Strike Time
Factory setting for Relays 1 and 2 is 01 (1 Second). Relays 3 through 8 are not set.
These steps will program the system relay strike times.
Strike times can be programmed from 1/4 second - enter 0 0 * in step 3, up to 99 seconds - enter 9 9 * in step 3.
System relays 1 and 2 are the two relays on the 1838’s main circuit board. System relays 3 through 8 are the relays
associated with additional RS-485 devices (card readers, keypads, RF receivers, etc.) connected to the system.
1.
Press
*
0 3 and enter the MASTER CODE.
[
*
0 3 _ _ _ _ (beep)]
2.
Enter a relay number (1 – 8), then press
*
.
[ _
*
(beep)]
3.
Enter the two-digit strike time (00-99), then press
*
.
[ _ _
*
(beep)]
4.
Repeat steps 2 and 3 to set other relay strike times if necessary.
5.
Press 0 # TOGETHER to end.
[0 # (beeeeeep)]
1.
Press
*
0 5 and enter the MASTER CODE.
[
*
0 5 _ _ _ _ (beep)]
2.
Enter a relay number (1 – 8), then press
*
.
[ _
*
(beep)]
3.
Choose and enter a four-digit tone open number code (see chart below), then press
*
.
[ _ _ _ _
*
(beep)]
If a tone open function is not desired, enter # in place of a number.
4.
Repeat steps 2 and 3 to set other relay tone open number(s) if desired.
5.
Press 0 # TOGETHER to end.
[0 # (beeeeeep)]
2.4.8 Tone Open Numbers
Factory setting is 9876 for Relay 1; 5432 for Relay 2. Relays 3 – 8 are not set.
These steps will program the tone open number(s) for each relay in the system (each relay is programmed independently).
You will need to enter a four-digit number (see chart below) to set each relay in step 3. If a function is not desired, enter #
in place of a number. Use a different number for each of the four-digits in step 3 when multiple functions are desired.
Example 1: If you want the relay to have a momentary activation function only, and you want the relay to activate when the
number 9 is pressed, enter 9 # # #
*
in step 3.
Example 2: If you only want the relay to hold open when the number 8 is pressed and the relay deactivated when the
number 7 is pressed, enter # 8 7 #
*
in step 3.
1st Digit (Step 3)
2nd Digit (Step 3)
3rd Digit (Step 3)
4th Digit (Step 3)
Momentary activation. The relay will activate for its programmed relay strike time.
Hold open. The relay will activate and remain activated until commanded to deactivate.
Deactivate relay.
Hold open 1 hour. The relay will activate for 1 hour and then deactivate itself.
4 Digit Tone Open Number Code
Function
2.4.9 Answer Incoming Call on X Rings (Phone Line Required)
Factory setting is 06 (6 Rings).
This programming section sets the number of rings that the 1838 will allow to pass through it before it picks up the call.
The number of rings to answer can be set from 1 to 99 rings and must be entered as a two-digit number.
For example, if you want the unit to answer the call after the sixth ring, enter 0 6
*
in step 2. If you program 0 0
*
in step
2, this will prevent (disable) the 1838 from answering incoming calls to it.
1.
Press
*
1 8 and enter the MASTER CODE.
[
*
1 8 _ _ _ _ (beep)]
2.
Enter the number of rings (01-99), then press
*
.
[ _ _
*
(beep)]
(enter 00 in this step to disable this feature)
3.
Press 0 # TOGETHER to end.
[0 # (beeeeeep)]
Summary of Contents for 1838 Access Plus
Page 39: ...1838 066 E 12 16 35...
