1838-066-E-12-16
24
2.6 Access Codes to Operate Access Control Devices
Note:
All access codes are five (5) digits in length.
If you make a mistake while programming steps, press “
0 #”
together and start at step 1 again.
2.6.4 Device Access Code Programming “Time Zone Restricted”
This programming sequence programs access codes into the system memory
with time zone restrictions
. It also allows
programming of the
access codes to momentarily activate a relay or to hold open (latch) a relay.
1.
Press
*
7 0 and enter the MASTER CODE.
[
*
7 0 _ _ _ _ (beep)]
2.
Enter the device type (0 = card, 1 = transmitter, 2 = keypad, 3 = other), then press
*
.
[ _
*
(beep)]
3.
Choose and enter a five-digit access code, then press
*
.
[ _ _ _ _ _
*
(beep)]
4.
Enter a minimum of 1, and a maximum of 4 time zones (valid time zones are 0 through 6) that you
want to apply to this access code, then press
*
.
[ _ _ _ _
*
(beep)]
Time zone 0 - Always deny access.
Time zone 1 - Allows 24/7 access for relay 1 and any additional relays.
Time zone 2 - Allows 24/7 access for relay 2 and any additional relays.
Time zones 3, 4, 5 and 6 - Are time zones that have been programmed in 2.7.6.
5.
Enter 0
*
for momentary relay activation or enter 1
*
to hold open (latch) the relay.
[ _
*
(beep)]
6.
Repeat steps 2 through 5 to program additional access codes (Time zone restricted).
7.
Press 0 # TOGETHER to end.
[0 # (beeeeeep)]
2.6.5 Delete an Access Code
This programming sequence
deletes individual
access codes that have been programmed into the 1838.
1.
Press
*
7 1 and enter the MASTER CODE.
[
*
7 1 _ _ _ _ (beep)]
2.
Enter the device type (0 = card, 1 = transmitter, 2 = keypad, 3 = other), then press
*
.
[ _
*
(beep)]
3.
Enter the five-digit device access code to be deleted, then press
*
.
[ _ _ _ _ _
*
(beep)]
See 2.6.1 and/or 2.6.4 for the five-digit access code.
4.
Repeat steps 2 and 3 to delete additional existing “simple” and “time zone restricted” access codes.
5.
Press 0 # TOGETHER to end.
[0 # (beeeeeep)]
2.6.6 Delete All Access Codes for the Same Type of Device
This programming sequence deletes
ALL
existing “simple” and “time zone restricted (TZR)” access codes
for the same
type of device.
To delete
ALL
existing “simple” and “time zone restricted” access codes, this programming sequence will
need to be preformed for each type of device that is connected to the system.
WARNING: Once started, all “simple” and “time zone restricted”
access codes for the same type of device will be erased.
1.
Press
*
7 2 and enter the MASTER CODE.
[
*
7 2 _ _ _ _ (beep)]
2.
Enter the device type (0 = card, 1 = transmitter, 2 = keypad, 3 = other), then press
*
.
[ _
*
(beep)]
3.
Press 9 9 9 9, then press
*
.
[ 9 9 9 9 (beep)]
4.
The programming sequence will end itself automatically.
[beeeeeep]
Summary of Contents for 1838 Access Plus
Page 39: ...1838 066 E 12 16 35...
