Digital Equipment DIGITAL Server 7100 1200 Service Maintenance Manual Download Page 77

Page: 77 / 162

Troubleshooting

4-32

Wide Ultra SCSI Bus Repeater Module
Troubleshooting

Problem

Possible Cause

Action

Server does not recognize an
internal wide Ultra SCSI device.

Wide Ultra SCSI bus repeater
module cables and/or power
cables not connected properly.

Make sure all cables are
connected as shown on the
Quick Reference labels
attached to the server’s side
panels.

Wide Ultra SCSI bus repeater
module not connected to all
wide Ultra SCSI buses.

Make sure a wide Ultra SCSI
bus repeater module is
connected to each wide Ultra
SCSI bus. Refer to the Quick
Reference labels.

SCSI bus repeater module
failed.

Remove the cables from the
bus repeater and connect the
cables from the SCSI adapter
and power supply directly to
the backplane. Reboot the
server. If the server boots
and the problem disappears,
replace the SCSI bus repeater
module.

Server unable to perform wide
Ultra SCSI data transfers

Did not run the SCSI or RAID
Configuration Utility.

Run the SCSI or RAID
configuration utility and enable
wide Ultra SCSI data
transfers.

Summary of Contents for DIGITAL Server 7100 1200



































































































































































Search results

Summary of Contents for DIGITAL Server 7100 1200

Reviews:

Related manuals for DIGITAL Server 7100 1200

Brands by name

Popular brands

Digital Equipment DIGITAL Server 7100 1200, Service Maintenance Manual

Search results

Summary of Contents for DIGITAL Server 7100 1200

Reviews:

Related manuals for DIGITAL Server 7100 1200

Brands by name

Popular brands