Digital Equipment DIGITAL Server 7100 1200 Service Maintenance Manual Download Page 21

Page: 21 / 162

Product Description

1-9

erve

er7

Latest Product Information and Updates

Listed below is the current product information and update source locations.

Enterprise Server Product Information

Family Name

Model Name

Part Number

Description

Prioris Family
Name

DIGITAL Server
7000

DIGITAL Server
7100 1200

FR-932WW-CX

6200/512 (PP) -
KERNAL

N/A

DIGITAL Server
7000

DIGITAL Server
7100 1200

FR-932WW-CA

6200/512 (PP) -
MODEL 1

N/A

DIGITAL Server
7000

DIGITAL Server
7100 1200

FR-932WW-CB

6200/512 (PP) -
RAID

N/A

PowerGrade Chip
Upgrade

DIGITAL Server
7000 PowerGrade
Kit

FR-PC93U-AD

6200/512 (PP)
PowerGrade Chip
Upgrade

Prioris ZX 6000
Series
PowerGrade

PowerGrade Board
Upgrade with
2 processors

DIGITAL Server
7000 PowerGrade
Kit

FR-PC93U-AB

6200/512 (PP)
PowerGrade
Board Upgrade

Prioris ZX 6000
Series
PowerGrade

Updates

Current server utilities and technical support information is available on the Quick
Launch CD-ROM disc and the Internet.

For product information, use the address:

http://www.windows.digital.com

For technical support, use the address:

http://www.windows.digital.com/support/support.asp

For access directly to the software library for BIOS and driver updates, use the
address:

http://www.windows.digital.com/~ftp/00-index.stm

Summary of Contents for DIGITAL Server 7100 1200



































































































































































Search results

Summary of Contents for DIGITAL Server 7100 1200

Reviews:

Related manuals for DIGITAL Server 7100 1200

Brands by name

Popular brands

Digital Equipment DIGITAL Server 7100 1200, Service Maintenance Manual

Search results

Summary of Contents for DIGITAL Server 7100 1200

Reviews:

Related manuals for DIGITAL Server 7100 1200

Brands by name

Popular brands