Digital Equipment DIGITAL Server 7100 1200 Service Maintenance Manual Download Page 45 | Manualshive

Page: 45 / 162

background image

SCU Features

3-12

EISA or PCI Devices Group

Menu Fields

Settings

Comments

EISA [slot#] - [device]

You can edit resources provided by the expansion
board’s vendor. Please refer to the menu
displayed on this item.

PCI [slot#] - [device]
PCI function 1

Enabled
Disabled

Whenever PCI devices are installed in the PCI
slots, the device is automatically added. You can
enable or disable this device. If enabled, you can
set the related resources based on the menu the
SCU displays.

Embedded - [device]
PCI function 1

Enabled
Disabled

Three kinds of PCI devices can be identified as
Embedded devices. The first are onboard PCI
devices. The second are the PCI devices beyond
10 PCI devices that have been identified and
shown as the normal PCI devices. The third are
the PCI devices that share the same IRQ with the
PCI devices displayed as the normal PCI devices.
When enabled, all the resources shown on the
menu can be changed.

Embedded - PCI VGA
controller
PCI function 1

Enabled
Disabled

Onboard PCI VGA device.

Standard VGA
resources

Enabled
Disabled

Enables or disables the compatible VGA
resources.

«
...
43
44
45
46
47
...
»

Summary of Contents for DIGITAL Server 7100 1200



































































































































































Reviews:

No comments

Related manuals for DIGITAL Server 7100 1200

SuperServer 1026T-M3

Brand: Supero Pages: 104

Netfinity 1000-8477 21Y

Brand: IBM Pages: 268

AssuredSAN 4004 Series

Brand: Dot Hill Pages: 59

Brand: Santec Pages: 40

Connectware PortServer TS 8/16

Brand: Digi Pages: 106

Brand: QSSC Pages: 97

RF-ENCO-IP-HDSDI-35

Brand: RFoG Pages: 67

Brand: IBM Pages: 86

Brand: IBM Pages: 90

306m - eServer xSeries - 8849

Brand: IBM Pages: 74

Brand: IBM Pages: 144

ETHERNETV 4410-0118-0009

Brand: VBrick Systems Pages: 202

SecureBox SDS2100

Brand: Lantronix Pages: 70

Brand: Lantronix Pages: 370

Brand: Acnodes Pages: 8

Brand: Iomega Pages: 8

Brand: Gateway Pages: 17

UniServer R6900 G3

Brand: H3C Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands