Digifly AIR-BT Owner'S Manual Download Page 26

Page: 26 / 96

AIR_Manual_506a_ENG_rev_1.pdf

Page 26/96



The A2 Altimeter is used for general purposes. To reset it LONG PRESS the

key. Note that

with the “Skip

Waypoint” shortcut parameter activated ADVANCED SETUP \ n. 24 SKPW=ON) the “OK” button will have a
different function: it will take you to the next waypoint on your route and will no longer zero the A2 altimeter



With the parameter MAIN SETUP \ n. 25 A2AU=ON, the AIR will automatically set the Altimeter 2 to zero, right

after launch.



The A3 Altimeter is automatically reset when you start thermalling.



The altimeters can be shown in meters (mt) or feet (ft), to set up, go to: MAIN SETUP \ n. 13 U-AL.

4.1.4

MAXIMUM ALTITUDE ALARM



This parameter (MAIN SETUP \ n. 40 A1AL) will notify you when you reach the set altitude; the alarm will be

reset once you go back down below the set threshold by 10m (33ft).



It ranges from 0 to 9,000ft (approx.. 29,500ft) and default setting is 0. Set to 0, the alarm is off.

Summary of Contents for AIR-BT

































































































Search results

Summary of Contents for AIR-BT

Reviews:

Related manuals for AIR-BT

Brands by name

Popular brands

Digifly AIR-BT, Owner'S Manual

Search results

Summary of Contents for AIR-BT

Reviews:

Related manuals for AIR-BT

Brands by name

Popular brands