![Dexter Laundry Wn0600ea-13en2x-sskcs-usx Parts & Service Manual Download Page 136](http://html1.mh-extra.com/html/dexter-laundry/wn0600ea-13en2x-sskcs-usx/wn0600ea-13en2x-sskcs-usx_parts-and-service-manual_2490411136.webp)
Part # 8533-097-001 11/16
136
Optional Steam Valve Kit
Features
When the numeric temperature value is programmed for any bath, the water valve selection to fill that bath
is
chosen
as
follows:
20 degrees - 35 degrees Centigrade
Cold valve only will be used
40 degrees - 60 degrees Centigrade
Cold and Hot valve will be used
65 degrees - 90 degrees Centigrade
Hot valve only will be used
The temperature control and display are controlled using the temperature control circuit board on the I/O
board, the thermistor sensor in the tub back, and the computor logic board (CPU). The contol voltage is 115
volts (60hz).
Operating Parameters
The programmed temperature will be displayed in Centigrade only.
The steam valve will be activated when the low water level has been reached and the actual water tempera-
ture
is
less
than
the
programmed
temperature.
While the steam valve is engaged, the cylinder will pause 3 minutes between each forward/reverse rota-
tion. The cylinder will resume normal operation once the water bath temperature is within 5 degrees of the
programmed temperature.
Cycle countdown time display will stop while valve is engaged.
During the cycle, if the water bath temperature drops 3 degrees below the programmed temperature, the
steam valve will engage to maintain the water temprature.
The actual water temperature will display by pressing the Start and Down arrows simultaneously. The tem-
perature light will be on whenever the temperature is being displayed. The temprature light will continue to
be displayed until the Start button is pushed again, changing the display over to time remaining.
The control can be programmed to maintain any temperature between 20 degrees and 90 degrees. The
programming
is
in
5
degree
increments.
Any bath that has a programmed spin cycle will go through a short cool down bath before spinning if the
actual bath temperature at the time of draining is above 65 degrees . This bath consists of filling tub to low
level with WARM water while tumbling and then draining. This will continue until bath temperature is below
65 degrees.
Summary of Contents for Wn0600ea-13en2x-sskcs-usx
