70
| Configuring AWMS
Dell PowerConnect W AirWave 7.1
| User Guide
1. To add a Cisco WLSE server to AWMS, navigate to the
AMP
Setup > WLSE
page and click
Add
.
Complete the fields in this page.
Table 33
describes the settings and default values.
2. After you have completed all fields, click the
Save
button. AWMS is now configured to gather rogue
information from WLSE rogue scans. As a result of this configuration, any rogues found by WLSE appear on
the
RAPIDS > Rogue
page.
What Next?
Navigate to additional tabs in the
AMP Setup
section to continue additional setup configurations.
Complete the required configurations in this chapter prior to proceeding to ensuing chapters of this document.
Dell support remains available to you for any phase of AWMS installation.
Table 33
AMP Setup > WLSE
Fields and Default Values
Setting
Default
Description
Hostname/IP Address
None
Designates the IP address or DNS Hostname for the WLSE server, which
must already be configured on the Cisco WLSE server.
Protocol
HTTP
Specifies the protocol to be used when polling the WLSE.
Port
1741
Defines the port AWMS uses to communicate with the WLSE server.
Username
None
Defines the username AWMS uses to communicate with the WLSE server.
The username and password must be configured the same way on the
WLSE server and on AWMS.
The user needs permission to display faults to discover rogues and
inventory API (XML API) to discover manageable APs. As derived from a
Cisco limitation, only credentials with alphanumeric characters (that have
only letters and numbers, not other symbols) allow AWMS to pull the
necessary XML APIs.
Password
None
Defines the password AWMS uses to communicate with the WLSE server.
The username and password must be configured the same way on the
WLSE server and on AWMS.
As derived from a Cisco limitation, only credentials with alphanumeric
characters (that have only letters and numbers, not other symbols) allow
AWMS to pull the necessary XML APIs.
Poll for AP Discovery; Poll for
Rogue Discovery
Yes
Sets the method by which AWMS uses WLSE to poll for discovery of new
APs and/or new rogue devices on the network.
Last Contacted
None
Displays the last time AWMS was able to contact the WLSE server.
Polling Period
10 minutes
Determines how frequently AWMS polls WLSE to gather rogue scanning
data.
Summary of Contents for PowerConnect W Airwave 7.1
