manualshive.com logo in svg

Dell PowerConnect 7024, Manual

The Dell PowerConnect 7024 is an advanced networking switch that offers high performance and reliability for your network infrastructure. To get started with this powerful device, you can easily download the free Getting Started Manual from our website. Explore its features and unleash its full potential for your network.

Share
Download
background image

274

Managing General System Settings

SDM Template Configuration Guidelines

When you configure the switch to use an SDM template that is not currently 

in use, you must reload the switch for the configuration to take effect.

If the IPv4 Routing or IPv4 Data Center template is currently in use and you 

attempt to configure IPv6 routing features without first selecting the Dual 

IPv4-IPv6 Routing template, the IPv6 commands do not take effect. IPv6 

features are not available when an IPv4-only template is active.

Why is the System Time Needed?

The switch uses the system clock to provide time stamps on log messages. 

Additionally, some 

show

 commands include the time in the command 

output. For example, the 

show users login-history

 command includes a Login 

Time field. The system clock provides the information for the Login Time 

field.

How Does SNTP Work?

SNTP assures accurate switch clock time synchronization. Time 

synchronization is performed by a network SNTP server. 
Time sources are established by Stratums. Stratums define the accuracy of 

the reference clock. The higher the stratum (where zero is the highest), the 

more accurate the clock. The switch is at a stratum that is one lower than its 

time source. For example, if the SNTP server in an internal network is a 

Stratum 3 device, the switch is a Stratum 4 device.
You can configure the switch to request the time from an SNTP server on the 

network, or you can allow the switch to receive SNTP broadcasts. 
Requesting the time from a unicast SNTP server is more secure. Use this 

method if you know the IP address of the SNTP server on your network. If you 

allow the switch to receive SNTP broadcasts, any clock synchronization 

information is accepted, even if it has not been requested by the device. This 

method is less secure than polling a specified SNTP server.

NOTE: 

If you attach a unit to a stack and its template does not match the stack's 

template, then the new unit will automatically reboot using the template used by 

the management unit. To avoid the automatic reboot, you may first set the 

template to the template used by the management unit. Then power off the new 

unit, attach it to the stack, and power it on.

Summary of Contents for PowerConnect 7024



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerConnect 7024

3Com 4210 Series Datasheet preview
4210 Series
Brand: 3Com Pages: 8
3Com PathBuilder S200 Series Feature Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 11
3Com 4400 Datasheet preview
4400
Brand: 3Com Pages: 8
3Com CoreBuilder 3500 Getting Started Manual preview
CoreBuilder 3500
Brand: 3Com Pages: 96
Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Brand: Cabletron Systems Pages: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Brand: Cabletron Systems Pages: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Brand: Cabletron Systems Pages: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Brand: Cabletron Systems Pages: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Brand: Cabletron Systems Pages: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 38
eao 04 Series Assembly Instructions preview
04 Series
Brand: eao Pages: 2
eao 04 Series Assembly Instruction preview
04 Series
Brand: eao Pages: 2
JB Systems Light SW-416 Operation Manual preview
SW-416
Brand: JB Systems Light Pages: 15
Xantech D5SH Installation Instructions Manual preview
D5SH
Brand: Xantech Pages: 20
Perel EMS113 User Manual preview
EMS113
Brand: Perel Pages: 4
Danfoss LLS 4000 Installation Manual preview
LLS 4000
Brand: Danfoss Pages: 6
Ihse Draco major K474-U8/C8 User Manual preview
Draco major K474-U8/C8
Brand: Ihse Pages: 167
steute Ex 95 SB Mounting And Wiring Instructions preview
Ex 95 SB
Brand: steute Pages: 10

Brands by name

Popular brands

Load more brands