manualshive.com logo in svg

Dell PowerConnect 7024, Manual

Share
Download
Dell PowerConnect 7024 Manual Download Page 845

Configuring Routing Interfaces

845

What Are Tunnel Interfaces?

Tunnels are a mechanism for transporting a packet across a network so that it 

can be evaluated at a remote location or

 tunnel endpoint

.  The tunnel, 

effectively, hides the packet from the network used to transport the packet to 

the endpoint.  This allows for the transmission of packets that the transport 

network cannot process directly, such as in one of the following cases:

• The packet protocol is not supported.
• The packet is in an incompatible addressing space.
• The packet is encrypted.  

PowerConnect 7000 Series switches support tunnels to encapsulate IPv6 

traffic in IPv4 tunnels to provide functionality to facilitate the transition of 

IPv4 networks to IPv6 networks. 
The switch supports two types of tunnels: configured (6-in-4) and automatic 

(6-to-4). Configured tunnels have an explicit configured endpoint and are 

considered to be point-to-point interfaces. Automatic tunnels determine the 

endpoint of the tunnel from the destination address of packets routed into 

the tunnel. These tunnels correspond to Non-Broadcast Multi-Access 

(NBMA) interfaces. A configured tunnel interface has a single tunnel 

associated with it, while an automatic tunnel interface has an infinite number 

of tunnels (limited only by the address encoding scheme).
Because tunnels are used as logical interfaces, you can define static routes 

that reference the tunnels. Additionally, dynamic routing can be configured to 

use the tunnels.

Why Are Routing Interfaces Needed?

The routing interfaces this chapter describes have very different applications 

and uses, as this section describes. If you use the switch as a layer 2 device 

that handles switching only, routing interface configuration is not required. 

When the switch is used as a layer 2 device, it typically connects to an 

external layer 3 device that handles the routing functions.

VLAN Routing

VLAN routing is required when the switch is used as a layer 3 device. VLAN 

routing must be configured to allow the switch to forward IP traffic between 

subnets and allow hosts in different networks to communicate.

Summary of Contents for PowerConnect 7024



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands