Dell P2423DE User Manual Download

Page: 87 / 94

Troubleshooting

│

Common problems

The following table contains general information about common monitor problems
you might encounter and the possible solutions:

Common
Symptoms

What you
experience

Possible Solutions

No Video/Power
LED off

No picture

Ensure that the video cable connecting
the monitor and the computer is properly
connected and secure.

• Verify that the power outlet is

functioning properly using any other
electrical equipment.

• Ensure that the power button is pressed.
• Ensure that the correct input source is

selected via the

Input Source

menu.

No Video/Power
LED on

No picture or no
brightness

• Increase brightness and contrast

controls using the OSD.

• Perform monitor self-test feature check.
• Check for bent or broken pins in the

video cable connector.

• Run the built-in diagnostics.
• Ensure that the correct input source is

selected via the

Input Source

menu.

Poor Focus

Picture is fuzzy,
blurry, or ghosting

• Eliminate video extension cables.
• Reset the monitor to Factory Settings

(

Factory Reset

• Change the video resolution to the

correct aspect ratio.

Shaky/Jittery
Video

Wavy picture or
fine movement

• Reset the monitor to Factory Settings

(

Factory Reset

• Check environmental factors.
• Relocate the monitor and test in another

room.

Summary of Contents for P2423DE































































































Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands

Dell P2423DE, User Manual

Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands