Dell P2423DE User Manual Download Page 68

Page: 68 / 94

│

Operating the monitor

Personalize

Brightness/Contrast

Input Source

2X Monitor

Color

Display

Personalize

Others

Exit

Shortcut Key 1

Input Source

Preset Modes

Brightness/Contrast

On in On Mode

Off in Off Mode

Off in Standby Mode

Off

Shortcut Key 2

Shortcut Key 3

Power Button LED

USB-C Charging 90W

Other USB Charging

Fast Wakeup

Reset Personalization

Shortcut Key 1

Allows you to choose a feature from

Preset Modes,

Brightness/Contrast, Input Source, Aspect Ratio,
Rotation,

Display Info

and set it as a shortcut key.

Shortcut Key 2
Shortcut Key 3

Power Button

LED

Allows you to set the power LED indicator On or Off to
save energy.

USB-C

Charging

90W

The default setting is

Off in Off Mode

. Selecting

in Off Mode

may automatically charge your notebook

or mobile devices through the USB-C cable even when
the monitor is in off mode.

Other USB

Charging

Allows you to enable or disable USB Type-A
(Downstream Ports) charging function during monitor
standby mode.

Fast Wakeup

The default setting is

Off

. Selecting

may prevent

the monitor from going into Standby mode.
Pressing or move the joystick (except the power
button) on the rear panel of the monitor may also wake
up the monitor after it goes into Standby mode.

Reset

Personalization

Resets all settings under the

Personalize

menu to the

factory preset values.

Summary of Contents for P2423DE































































































Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands

Dell P2423DE, User Manual

Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands