Dell P2423DE User Manual Download Page 30 | Manualshive

Page: 30 / 94

background image

30

│

About your monitor

Driver installation

Install the Realtek USB GBE Ethernet Controller Driver available for your system.
This is available for download at

www.dell.com/support

under the “Driver and

download” section.
Network (RJ45) data rate via USB-C max speed is 1000 Mbps.

NOTE: This LAN port is 1000Base-T IEEE 802.3az compliant,

supporting Mac Address (Printed on model label) Pass-thru (MAPT),
Wake-on-LAN (WOL) from standby mode (S3 only) and UEFI* PXE
Boot function [UEFI PXE Boot is not supported on Dell Desktop PC’s
(except for OptiPlex 7090/3090 Ultra Desktop)], these 3 features
depend on BIOS settings and version of the OS. Functionality may vary
with Non Dell PC’s.

*UEFI stands for Unified Extensible Firmware Interface.

RJ45 connector LED status

«
...
28
29
30
31
32
...
»

Summary of Contents for P2423DE































































































Reviews:

No comments

Related manuals for P2423DE

Brand: Bacharach Pages: 5

10.4" TFT LCD Ceiling Monitor

Brand: Farenheit Pages: 11

Brand: Valeo Pages: 124

SyncMaster S24B750V

Brand: Samsung Pages: 98

Brand: Alecto Pages: 25

Brand: Westinghouse Pages: 4

Brand: max mobility Pages: 12

Brand: Digimate Pages: 22

Brand: Contec Pages: 2

VA1926W - 19" LCD Monitor

Brand: ViewSonic Pages: 25

Brand: SWIT Pages: 12

Brand: ViewSonic Pages: 16

Life Source UA-851THW

Brand: A&D Pages: 72

Brand: Atari Pages: 23

Brand: BabySense Pages: 18

Brand: Maxent Pages: 30

MultiSync EX241UN-PT-H

Brand: NEC Pages: 34

MultiSync FE750 JC-17W40

Brand: NEC Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands