Dell P2423DE User Manual Download Page 40

Page: 40 / 94

│

Setting up the monitor

Connecting your monitor

WARNING: Before you begin any of the procedures in this section,
follow the

Safety instructions

NOTE: Dell monitors are designed to work optimally with Dell

supplied inbox cables. Dell does not guarantee the video quality and
performance if non-Dell cables are used.

NOTE: Route the cables through the cable-management slot before

connecting them.

NOTE: Do not connect all cables to the computer at the same time.

NOTE: The images are for the purpose of illustration only. The

appearance of the computer may vary.

To connect your monitor to the computer:

Turn off your computer and disconnect the power cable.

Route the power cable through the cable-management slot on the stand and
then connect it to the monitor.

Connect the DisplayPort, HDMI, USB-C (C-C), or USB-C (C-A) cable from
your monitor to the computer.

Summary of Contents for P2423DE































































































Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands

Dell P2423DE, User Manual

Search results

Summary of Contents for P2423DE

Reviews:

Related manuals for P2423DE

Brands by name

Popular brands