Deagostini MODEL SPACE Lamborghini Countach LP 500S Assembly Manual Download Page 2

Page: 2 / 28

Lamborghini Countach LP 500S

™

Assembly Guide Stages 78-80

450

CONTENTS

Stage 78 - The right door

Stage 79 - Assembling the body

Stage 80 - Completing your model

Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.

Published in the UK by De Agostini UK Ltd, Battersea Studios 2,

82 Silverthorne Road, London SW8 3HE.

Published in the USA by De Agostini Publishing USA, Inc., 915 Broadway, Suite 609,

The trademarks, copyrights and design rights in and associated with the following

Lamborghini vehicles Countach LP500S are used under licence from

Automobili Lamborghini S.p.A., Italy.

NOT SUITABLE FOR CHILDREN UNDER THE AGE OF 14. THIS

PRODUCT IS NOT A TOY AND IS NOT DESIGNED OR INTENDED

FOR USE IN PLAY. ITEMS MAY VARY FROM THOSE SHOWN.

The rear hubs shown in this pack are the old version

and so will differ from the ones on your model, which

are the updated versions from Packs 12 and 13.

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S





























Search results

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S

Reviews:

Related manuals for MODEL SPACE Lamborghini Countach LP 500S

Brands by name

Popular brands

Deagostini MODEL SPACE Lamborghini Countach LP 500S, Assembly Manual

Search results

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S

Reviews:

Related manuals for MODEL SPACE Lamborghini Countach LP 500S

Brands by name

Popular brands