Deagostini MODEL SPACE Lamborghini Countach LP 500S Assembly Manual Download Page 19 | Manualshive

Page: 19 / 28

background image

466

Lamborghini Countach LP 500S

Check that the circled holes in the underbody are aligned with the holes in the posts
on the main body. If any don’t line up, separate the main body and the underbody,
and adjust the fit until the holes align.

Insert the tip of the steering shaft into the steering crank.

Combine the posts and holes at the sides of the model, as shown.

Adjust the position of the radiators, fitting them
into the recesses in the underbody.

18

«
...
17
18
19
20
21
...
»

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S





























Reviews:

No comments

Related manuals for MODEL SPACE Lamborghini Countach LP 500S

Brand: Schumacher Pages: 30

Brand: Serpent Pages: 58

Bentley Continental GT3

Brand: Jamara Pages: 2

Brand: Active Intent Pages: 10

Brand: AE Pages: 30

Brand: Kyosho Pages: 39

Mini-Z Racer MR-015 RM Type

Brand: Kyosho Pages: 2

MINI-Z Racer MR-02 RM Type

Brand: Kyosho Pages: 28

LAZER ZX-5 Readyset

Brand: Kyosho Pages: 24

Brand: Kyosho Pages: 42

Brand: Kyosho Pages: 41

Brand: Kyosho Pages: 57

Brand: Jamara Pages: 12

Brand: RB Pages: 35

Brand: NORDIC PLAY Pages: 20

Brand: Jamara Pages: 12

Brand: GL Racing Pages: 24

Brand: Kyosho Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands