background image

474

Lamborghini Countach LP 500S

The headlamps

To raise the headlamps, push the part of the 
headlamp link bar projecting from the underbody 
(circled). To lower the lamps, gently push them back 
down again.

The steering

The front wheels can be moved left or right by 
turning the steering wheel. However, because of the 
weight of the model, it is recommended that you lift 
the front of the car slightly when operating the 
steering wheel.

The doors

To open the door, push up on the door lock (circled), 
and then lift the door up. To close the door, push it 
back down until you feel a click as it locks into place.

Pressing the accelerator pedal (far right) while the 
ignition key is in the cylinder will rev the engine, and 
pressing the brake pedal (centre) will illuminate the 
brake lights.

The steering column switches

The left steering column lever has two 
functions: pushing the lever in will sound 
the horn, and pulling it back will turn the 
lights on. Pulling it back again will turn 
the high beam on, and pulling it a third 
time will turn the lights off. When you 
insert the ignition key into the cylinder, 
the engine sound will start.

The covers

The bonnet and rear compartment cover are opened 
and closed manually, and held up by the extending 
stays. To hold the engine cover open, insert the end 
of the stay into the hole in the wheel box.

The pedals

Pushing the lever in will 

sound the horn.

Pulling the lever back will cycle through 

the light options.

Inserting the key will 

start the engine sound.

Operating the parts

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S





























Reviews: