Deagostini MODEL SPACE Lamborghini Countach LP 500S Assembly Manual Download Page 26

Page: 26 / 28

473

Lamborghini Countach LP 500S

Tighten a second 2 × 5mm self-
tapping screw into the hole on the
opposite side of the cover, to fix the
rear wing in position.

Tighten a 1.7 × 4mm self-tapping screw
into the hole. The stay must be able to
rotate slightly, so leave the screw undone
by about half a turn.

Tighten the screw into place.

Apply masking tape to the protective covers on the
indicator lamps and peel them off.

Extend the cover stay and align the hole
at the end of it with the hole in the right
rear wheel box.

Congratulations! Your model is now complete.
The next page will show you how to operate its
working parts.

MODEL COMPLETE

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S





























Search results

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S

Reviews:

Related manuals for MODEL SPACE Lamborghini Countach LP 500S

Brands by name

Popular brands

Deagostini MODEL SPACE Lamborghini Countach LP 500S, Assembly Manual

Search results

Summary of Contents for MODEL SPACE Lamborghini Countach LP 500S

Reviews:

Related manuals for MODEL SPACE Lamborghini Countach LP 500S

Brands by name

Popular brands