background image

54 

TC3 Series Traction Control 

www.moretraction.com 

Disclaimer

 

FOR RACING PURPOSES and OFF-ROAD USE ONLY!

 

Vehicle racing is an inherently dangerous sport with significant risk of personal injury 
or even death. When a user participates in vehicle racing and/or track events, he 
accepts the risk inherent therein.

 

Davis Technologies LLC ("DAVIS"), its employees, 

and affiliates makes no warranty that the use of its products or parts guarantees 
personal safety or freedom from physical injury or operates as a life saving device. 

Davis Technologies LLC’s ("DAVIS")

 

PRODUCTS AND PARTS ARE SOLD "AS 

IS" WITHOUT ANY WARRANTY WHATSOEVER. EXPRESS WARRANTIES, 
IMPLIED WARRANTIES, WARRANTIES OF MERCHANTABILITY AND 
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. 
THE ENTIRE RISK OF QUALITY AND PERFORMANCE OF SUCH PRODUCTS 
AND PARTS IS WITH THE BUYER, USER, SUBSEQUENT USER, OR AGENT 
THEREOF (HEREIN "USER"). SHOULD SUCH PRODUCTS OR PARTS PROVE 
DEFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER AND NOT THE 
MANUFACTURER(S), DISTRIBUTOR(S), OR RETAILER(S), ASSUME THE 
ENTIRE COST OF ALL NECESSARY SERVICES OR REPAIR AS RESULT OF A 
PART(S) FAILING.

 

Davis Technologies LLC ("DAVIS") disclaims all liability for any special, direct, 
incidental or consequential damages, or any damages whatsoever, including, without 
limitation, the loss of life or limb, or damages due to bodily or personal injury, which 
may arise or result from the sale, installation, or use of any of its products and parts. 

It is the user's responsibility to inspect and verify the dimensions, specifications, and 
performance of all products and parts as being appropriate for the use to which the 
user will put them prior to any actual installation and/or use of said products and 
parts. 

Davis Technologies LLC’s ("DAVIS") products and parts are to be inspected by the 
user before each use for evidence of damage, defect or wear. Any deviation by the 
user from the manufacturer's specifications concerning use, maintenance, repair, 
alterations, and modifications constitutes willful negligence. 

The installation of Davis Technologies LLC’s ("DAVIS") products or parts may 
adversely affect other vehicle components, safety equipment or manufactured goods 
(collectively "goods"). Davis Technologies LLC ("DAVIS") assumes no responsibility 
for any damage to other goods, or bodily injury that may arise due to failure of other 
goods, due to installation and/or use, either proper or improper, of its products or 
parts. 

The liability of Davis Technologies LLC ("DAVIS")  is limited to the replacement of 
defective products or parts found under examination by manufacturer to be defective 
in material or workmanship within 60 days after purchase, and which has not been 
caused by an accident, improper use, alteration, tampering, excessive use, misuse, 

Summary of Contents for TC-3 Series





























































Reviews: