Datafox EVO 3.5 Pure Manual Download | Manualshive

Page: 7 / 135

background image

Handbuch Datafox EVO 3.5 Pure

Seite 1

Datum: 06.08.2018 Version: 04.03.07.XX

1.

For you Safty

Safety Information for Datafox Products

The EVO 3.5 Pure must only be operated according to the instructions

given in the manual.

Do no insert any foreign objects into the openings and ports.

The device must not be opened. All maintenance work must only

be performed by authorized specialists.

Some devices contain a lithium ion battery or a lithium battery.

Do not throw into fire!

Achtung!

Supply voltage:

12 Volt DC

Siehe jeweiliges Typenschild / technische Daten.

See respective type label / technical data.

The device must only be operated with a power-limited power supply

according to EN 60950-1. If you do not observe these instructions,

the device may be damaged.

The following temperature ranges must be observed

Working area / storage temperature:

-20° C bis +70° C

Mobile communications module:

-20° C bis +55° C

In areas with cellphone ban, GSM, WLAN and other cellular modems

must be turned off.

Persons with heart pacemakers:

When using the device, maintain a distance of at least 20 cm between the

heart pacemaker and the device in order to avoid possible interferences.

Turn the device off immediately if interferences are assumed.

Protection class:

Observe the technical data of the respective device.

In case of laser devices of class 2, the eye is protected by the blink reflex
and/or turning reactions if you briefly and accidentally look into the laser
beam. The devices may be used without further protective measures. Never-
theless, avoid looking directly into the laser beam of the laser scanner.

Observe the additional notes in the chapter,
“

Proper use and environmental protection

”

We declare under our sole responsibility that the product described fullfills the
protection requirements of European Directive 89/336 / EEC as amended by
91/236 / EEC, 92/31 / EEC, 93/97 / EEC and 93/68 /. See the manual of the
devices for the standards. Evidence is provided by compliance with the follow-
ing standards:

-

EN 55022 : 2006 + A1:2007

-

EN 55024 : 2003

-

EN 61000

– 6 – 2: 2005

-

IEC 61000-3-2 : 2005 + A1:2008 + A2:2009

-

IEC 61000-3-3 : 2008

«
...
5
6
7
8
9
...
»

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Related manuals for EVO 3.5 Pure

Brand: Firich Enterprise Pages: 49

Brand: Ingenico Pages: 2

Brand: Jobsite Pages: 4

Brand: adyen Pages: 10

Brand: Terasic Pages: 48

Brand: Pax Technology Pages: 7

Brand: Pax Technology Pages: 8

Brand: PAX Computer Technology Pages: 8

Brand: Fametech Pages: 22

Contactless and Chip Reader

Brand: Square Pages: 12

Brand: Square Pages: 16

Brand: K?Monitor Pages: 23

Brand: POSIFLEX Pages: 16

Brand: Magtek Pages: 75

Brand: Jepower Pages: 9

Brand: ACD GRUPPE Pages: 65

Brand: ZKTeco Pages: 61

Ingenico Move/5000

Brand: EMS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands