manualshive.com logo in svg

Datafox EVO 3.5 Pure, Manual

Share
Download
Datafox EVO 3.5 Pure Manual Download Page 104

 

Handbuch Datafox EVO 3.5 Pure 

Seite 98 

    Datum: 06.08.2018  Version: 04.03.07.XX 

5.9.7.5.  Liste Presence  

 
This list is created by the access controller itself. 
This makes it possible to enable the tracking of people and rooms via several access controllers. 
If the Antipassback function is to be used via several access controllers, this list must always be up-
dated by the software to all access controllers. 
 

Example: 

A room (example room ID 10) has several doors that are managed by different access control box-
es. If a person enters this room, an entry is created in the Presence list of this box that this person is 
in the room. 
 
The other access control boxes can now also be informed that the person with ID X is in room 10. 
To do this, an entry in the Presence list must be created in the other boxes via your software (with 
DLL). 
This is done using the method 

DFCTableAppendRowData

 Append Data Row to the table. 

The same applies if a person leaves the room, this entry must be deleted in the Other Access Con-
trol Boxes. 
 

Name 

Data type

 

Length

 

Description 

ID

 

Number 
(int)

 

4

 

ID of the person that is stored in the presence list. 

RefLocation

 

Number 
(int)

 

4

 

Reference to the ID of the room, defined in the table "Location", where this per-
son currently stays 

TimeStamp 

Number 
(int) 

10 

Time stamp when the person entered the current room 
Integer in seconds, starting 01.01.2000. 

 

 
 

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands