Datafox EVO 3.5 Pure Manual Download Page 123

Page: 123 / 135

Handbuch Datafox EVO 3.5 Pure

Seite 117

Datum: 06.08.2018 Version: 04.03.07.XX

5.11.3.

DataOnCard on the access control reader

In order to be able to use on a standard ZK reader of the EVO or the PHG series, the following set-
tings must be made.

The functions for DataOnCard described in the previous chapters can only be set in the setup under
Control menu.

Now it is necessary to be able to access the

access control reader

under the control.

This is how you set it:

The reader on the

access control reader

(ZK) bus (RS485) is now activated via the Control menu

(Transponderleser der Bedienung)



Please note:

Only one

access control reader

(ZK) can be connected to the bus at any time.

Dip switch 1 and the termination of the bus must be set to "ON"
(Bus address 1).

Summary of Contents for EVO 3.5 Pure








































































































































Search results

Summary of Contents for EVO 3.5 Pure

Reviews:

Related manuals for EVO 3.5 Pure

Brands by name

Popular brands

Datafox EVO 3.5 Pure, Manual

Search results

Summary of Contents for EVO 3.5 Pure

Reviews:

Related manuals for EVO 3.5 Pure

Brands by name

Popular brands