manualshive.com logo in svg

Datafox EVO 3.5 Pure, Manual

Share
Download
Datafox EVO 3.5 Pure Manual Download Page 15

 

Handbuch Datafox EVO 3.5 Pure 

Seite 9 

    Datum: 06.08.2018  Version: 04.03.07.XX 

4. 

System Requirements / Hardware 

4.1. 

System Structure 

The system consists of the Datafox device, the DatafoxStudioIV, the communication DLL and a 
software for processing the generated data. 

 
 

4.2. 

Requirements for Operating Datafox Devices 

In order to operate the Datafox device, you need a 230 V power connection for the Datafox power 
supply. Depending on the main communication set, you need a corresponding transfer medium or 
connection cable. 
Main communication: 

  USB > one standard USB-A toUSB-mirco Cable (see the chapter connection USB). 

  RS485 > a transmission path in accordance with the EIA-485 standard (see Connection 

RS485). 

  GSM/GPRS > a distortion-free mobile connection (see Connection GSM).  

  WLAN WiFi> a distortion-free channel to an access point (802.11 b/g) within reach (see 

Connection WLAN).  

 

at least one standard Ethernet cable, no „cross over“ (see Connection TCP) 

  HTTP(internet) via LAN > TCP/IP connection with free internet access. The data are sent 

to a server. 

 

 

Note: 

With increasing demands on transfer rate and interference immunity, the demands 
on the transmission path increase as well with regard to quality (interference immuni-
ty). 

 

Setup 

Create setup

 

Save setup

 

Transfer setup to device

 

Software for processing the generated data 

DatafoxStudioIV 

Communication- DLL 

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands