manualshive.com logo in svg

Datafox EVO 3.5 Pure, Manual

Share
Download
Datafox EVO 3.5 Pure Manual Download Page 73

 

Handbuch Datafox EVO 3.5 Pure 

Seite 67 

    Datum: 06.08.2018  Version: 04.03.07.XX 

If the device MasterIV is used for access control, door 
supervision or remote monitoring, one device can su-
pervise up to 8 doors and control 12 doors at most. 
 

diensions:  81 x 81 x 19 mm (BxHxT) 
 
The EVO acceess reader can be used with 125 kHz, Legic or Mifare. 
It is available for in-wall or on-wall mounting with or without key-
board. Each reader has a sabotage recognition, three lamps for vis-
ualizing the state and a buzzer for the acoustic signaling. 

Signals from the backlight:  
white permanent  = Reader found an ready 
white flashing     = reader not found and not connection to the master 

Signals from the backlight:  

green

 = access accept 

Signals from the backlight:  

red

 = access denied or the master configured the read-

er currently. 

5.9.3.  Access control wiht EVO-access modules 

The following hardware is available to set up an access control with EVO-modules. The devices can 
be combined in different ways according to their hardware requirements. 
 
EVO 3.5 Pure 
 

 

 

EVO-access-reader

 

 
 
 
 
 
 
 
 

 

IO-modul for EVO-Access reader

 

 

 

 

 

 

 

 

 

Display 

Backlit transponder symbol 

3-coloured white, green, red 

Individualization

 

Integrated backlight 

Individual printable front glass with backlight 56 x 37mm 

 

Colour always like transponder symbol 

power supply 

10 - 30V DC, max. 120mA 

 

Environment values

 

Ambient temperature, Protection 

-20 ° C to +70 ° C,  IP65 

Transponder systems 

125kHz 

Mifare 

Legic 

Hitag 1+2+S

 

Mifare Classic

 

Legic prime

 

Unique EM4102

 

Mifare Desfire

 

Legic advant

 

Titan EM4450

 

Mifare Ultralight

 

 

DGND

 

D IN1

 

Relay 

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands