Datafox EVO 3.5 Pure Manual Download Page 122

Page: 122 / 135

Handbuch Datafox EVO 3.5 Pure

Seite 116

Datum: 06.08.2018 Version: 04.03.07.XX

Example for Data on Card

ID with serial number:

1848989745

List entry for

1848989745

in the file before transferring to the device

Field ID Field Data (binary field) here as hex bytes

1848989745

3031323334353637383941424344454630313

2333435363738394142434445463031323334353637383941 ……

Data after conversion or within the device
Field ID Field Data (binary field) is binary here

1848989745

0123456789ABCDEF0123456789ABCDEF0123456789A …..

The following data will be writen on the ID card:

0123456789ABCDEF0123456789ABCDEF0123456789A …..

Binary the data looks like this:
0x30, 0x31, 0x32, 0x33, 0x34

……



Please note:

When a 3-tone sequence is signaled, the Data-On-Card option is not available on this de-
vice. The option has to be purchased afterwards.

Summary of Contents for EVO 3.5 Pure








































































































































Search results

Summary of Contents for EVO 3.5 Pure

Reviews:

Related manuals for EVO 3.5 Pure

Brands by name

Popular brands

Datafox EVO 3.5 Pure, Manual

Search results

Summary of Contents for EVO 3.5 Pure

Reviews:

Related manuals for EVO 3.5 Pure

Brands by name

Popular brands