Datafox EVO 3.5 Pure Manual Download Page 79 | Manualshive

Page: 79 / 135

background image

Handbuch Datafox EVO 3.5 Pure

Seite 73

Datum: 06.08.2018 Version: 04.03.07.XX

The bus terminating resistor of 120 Ω is switched on or off in
the bus configuration under "Terminating resistor".

Note: If it is the last or only reader in the RS485 bus, the termi-
nating resistor must be switched on.

The bus address is defined in the bus configuration under
"Bus number" .
Note that only bus addresses between 1 and 16 are possi-
ble.

The input of the bus number is confirmed with the "Enter"
key (bottom right).

With the Escape button (bottom left) the process can be
aborted.
Im Auslieferungszustand ist die Bus

– Adresse 1 gesetzt.

5.9.4.7. Display configuration

The following parameters can be set in the display configuration:

- the brightness of the device
- random number keys - arrangement of the pin and keyboard
- the basic activation of the pin - keyboard

5.9.4.8. Bus configuration

In the bus configuration, the initial parameters that are used
for the setup of the reader must be set, configured.

5.9.4.9. Setting the bus adress of the reader for RS485 bus

5.9.4.10. Activate the resistor for the end

«
...
77
78
79
80
81
...
»

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Related manuals for EVO 3.5 Pure

DS-K5672 Series

Brand: HIKVISION Pages: 2

Brand: Elo TouchSystems Pages: 33

Brand: M-system Pages: 2

Brand: FingerTec Pages: 32

Brand: Burnside Pages: 2

Brand: Burnside Pages: 24

Brand: Element Pages: 33

Brand: Kestronics Pages: 40

E-Touch Integrated

Brand: E-Pos Pages: 26

Brand: Newland Pages: 44

Brand: ICP Pages: 8

DynaPro 30056072

Brand: Magtek Pages: 40

Brand: ratiotec Pages: 20

Brand: EBN Pages: 45

Brand: TD Pages: 12

Brand: Partner Pages: 52

Brand: Omnicomm Pages: 68

Brand: National Instruments Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands