manualshive.com logo in svg

Datafox EVO 3.5 Pure, Manual

Share
Download
Datafox EVO 3.5 Pure Manual Download Page 53

 

Handbuch Datafox EVO 3.5 Pure 

Seite 47 

    Datum: 06.08.2018  Version: 04.03.07.XX 

5.8.7.  Communication via Cellular Network (GPRS) 

 
 
The EVO 3.5 Purecan be equipped with a cellular network modem. It enables the communication 
via cellular network. The antenna is located in the connection compartment of the device and can 
optionally be replaced by an external antenna if reception is bad. 
The SIM card is inserted via the connection compartment of the EVO 3.5 Pure. 
 
Einsetzen der Sim-Karte beim Gerät 
 
 
 
 
 
 
  

! 

Caution: 

For inserting the SIM card a tool in pen or screwdriver form is required. Take care that 
the SIM card is not damaged. 

 
For removing, the SIM card has to be pushed in a bit. After releasing it, the SIM card protrudes a bit 
and can be removed. 
 

 

Hinweis: 

Wir empfehlen T-Mobile oder Vodafone als Provider für Mobilfunk einzusetzen! Un-
sere Erfahrung zeigt, dass bei anderen Anbietern mit häufigeren Einwahlen und da-
mit auch verzögerter Datenübertragung und ggf. mit höheren Kosten gerechnet wer-
den muss. 

 
Informationen zu M2M:  

http://www.t-mobile.de/business/machinetomachine/m2m-im-einsatz/0,23219,26762-_,00.html

 

 

Summary of Contents for EVO 3.5 Pure








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands