DataCard SD Series Page 65 User Manual Download

Page: 65 / 106

SD Series Card Printers User’s Guide

Topcoat Appearance Problems

Problem

Probable Cause

Solution

There are scratches in

the topcoat.

The inside of the printer

is dirty.

Clean the printer. Refer to

“Run a Printer

Cleaning Card”

page 30

The supplies have

debris on them.

Store and handle supplies carefully. Keep

supplies in the original packaging until

you are ready to use them.

There are repeating

marks in the topcoat.

The heated roller is

dirty.

Clean the laminator. Refer to

"Clean the

Laminator"

page A-12

. If the problem

continues to occur, contact your service

provider.

The holographic

topcoat shows irregular

darker areas.

The temperature for

applying the

holographic topcoat is

too high.

Decrease the laminator temperature for

the overlay material. Refer to the Printer

Manager “Laminate Type” section of the

printer’s

Installation and Administrator’s

Guide

There are particles of

holographic topcoat

beyond the trailing

edge of the card.

The temperature for

applying the

holographic topcoat is

too high.

•

Topcoat particles, or flash, can

become attached to the card. Try

to brush off the particles.

•

Clean the laminator. Refer to

"Clean the Laminator"

page

A-12

•

Decrease the laminator

temperature for the overlay

material. Refer to the Printer

Manager “Laminate Type” section

of the printer’s

Installation and

Administrator’s Guide

Note:

Reducing the temperature can

reduce the number of particles, but does

not eliminate them.

The topcoat shows

wavy lines along the

length of the card.

The temperature for

applying the topcoat is

too high.

Decrease the laminator temperature for

the overlay material. Refer to the Printer

Manager “Laminate Type” section of the

printer’s

Installation and Administrator’s

Guide

The topcoat is spotty,

especially on the

leading edge of the

card.

The overlay material is

wound in the wrong

direction on the take-

up spool.

Process another card to allow the overlay

material to reset itself. If it doesn’t, remove

the cartridge and turn the take-up spool

clockwise several turns.

Summary of Contents for SD Series











































































































Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands

DataCard SD Series, User Manual

Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands