DataCard SD Series Page 89 User Manual Download

Page: 89 / 106

SD Series Card Printers User’s Guide

505: USB communication issue

important

driver

component

not

running.

The

card

will

canceled.

Restart

the

computer.

The

component

should

start

automatically.

this

message

displayed

after

restarting,

notify

your

printer

support

contact.

Click

clear

the

message.

506: A card is currently processing

The

printer

busy

processing

interactive

job.

The

card

will

canceled.

Wait

until

the

current

card

complete

and

then

try

again.

Click

clear

the

message.

508: The printer is shutting down

The

printer

shutting

down

resetting.

The

card

will

canceled.

When

printer

powered

back

on,

try

again.

Click

clear

the

message.

509: The printer is offline or suspended

The

printer

must

online

print.

complete

the

current

card

press

the

printer’s

SER

button

until

the

printer

returns

the

Ready

state.

Click

clear

the

message,

click

Cancel

cancel

the

card.

Summary of Contents for SD Series











































































































Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands

DataCard SD Series, User Manual

Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands