DataCard SD Series Page 94 User Manual Download

Page: 94 / 106

A-4

SD460 Laminating System

Inside the Laminator

The

SD460

system

has

one

standard

laminator,

the

position,

with

optional

second

laminator

the

position.

The

laminators

apply

topcoat

patch

overlay

material

the

card.

Topcoat

continuous

film

and

patch

die

‐

cut

polyester

shape.

Both

laminators

can

apply

either

overlay

type.

Refer

"Laminator

Overlay

Materials"

page

‐

Manual Advance

Knobs

The manual advance knobs move the card through

the laminator to remove it from the system. Use the

knobs to clear a card jam.

L1 Laminator (green

cartridge)

The L1 laminator cartridge holds overlay material and

applies it to the card.

L2 Laminator (orange

cartridge)

The L2 laminator cartridge holds overlay material and

applies it to the card. The L2 laminator is optional.

Laminator Access Door

The access door provides access to the L1 and L2

laminators to load supplies or to clear a card jam.

L2 Transport Access

Door

The L2 transport access door replaces the L2

laminator cartridge if the optional L2 laminator is not

installed. Open the door to access the laminator

card transport.

Laminator
Access Door

Manual Advance
Knobs

L1 Laminator

L2 Laminator

L2 Transport
Access Door

Summary of Contents for SD Series











































































































Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands

DataCard SD Series, User Manual

Search results

Summary of Contents for SD Series

Reviews:

Related manuals for SD Series

Brands by name

Popular brands