manualshive.com logo in svg

DataCard SD Series, User Manual, Page: 25 / 106

Share
Download
DataCard SD Series User Manual Download Page 25

SD Series Card Printers User’s Guide

13

 

Printer Controls

The

 

front

 

panel

 

of

 

the

 

printer

 

provides

 

the

 

controls

 

for

 

operating

 

the

 

printer.

 

The

 

front

 

panel

 

controls

 

are

 

described

 

in

 

the

 

following

 

sections.

Power Button

Use

 

the

 

P

OWER

 

button

 

to

 

power

 

off

 

and

 

power

 

on

 

the

 

printer.

 

All

 

lights

 

show

 

steady

 

amber

 

while

 

the

 

printer

 

powers

 

on.

To

 

power

 

off

 

the

 

printer,

 

press

 

the

 

button

 

for

 

1

 

to

 

2

 

seconds

 

until

 

the

 

printer

 

begins

 

to

 

shut

 

down.

 

To

 

power

 

off

 

the

 

printer

 

while

 

it

 

is

 

processing

 

cards,

 

press

 

the

 

button

 

for

 

2 seconds

 

or

 

more.

 

Card

 

jobs

 

in

 

the

 

printer

 

are

 

not

 

completed.

LCD Panel

Status Lights

Ribbon
Cards

User Light & 
User Button

Up 
Arrow

Enter

Down 
Arrow

Power 
Button

Summary of Contents for SD Series











































































































Reviews:

No comments