DAPAudio M9000 User Manual Download Page 7

Page: 7 / 122

1.0 Introduction

1.1 User and Product Safety

• Do not stare into the laser or LED beam directly or shine it into eyes.
• Never use strong pressure onto the screen or subject it to severe im

pact, as the LCD panel could become cracked and possibility cause

personal injury. If the LCD panel is broken, never touch the liquid

inside because the liquid irritates the skin.

• Although the PDT has passed the test of IP65 standard for water and

dust resistance, avoid prolonged exposure to rain or other concentrat-

ed moisture. Such condition exceeds the IP65 standard, and could

result in water or other contaminants entering into the PDT.

• Use only the original approved AC Adapter with the PDT. Use of an

unapproved AC Adapter could result in electrical problems, or even

cause a fire or electrical shock to the user.

• Do not disassemble the PDT. Servicing should be done by supplier

only. If the PDT or accessories gets damaged due to wrong handling

or unauthorized repair, warranty is void. In case the warranty seals

are broken, warranty is void too.

• Make regularly back-up of all important data.
• Under no circumstance will supplier be liable for any direct, indirect,

consequential or incidental damages baring out of the use or inability

to use the hardware and software and/or any data loss, even if sup-

plier has been informed about the possibility of such damages.

• LASER RADIATION: DO NOT STARE INTO BEAM CLASS 2 LA

SER PRODUCT.

1.2 LED and LASER Safety

Information

•   M9000 is a Class II LED/Laser Product.
•   DO NOT STARE at the LED/Laser or shine into eyes.
•   Do not allow young children to use the product without adult super

vision.

• Do not replace/repair the LED/Laser; these are not user replaceable.
• Do not shine the LED/Laser on a shiny reflective surface.

1.3 FCC Interference Statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

1.0 Introduction

–

RADIATION EXPOSURE STATEMENT

–

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. End users must follow

the specific operating instructions for satisfying RF exposure

compliance. To maintain compliance with FCC RF exposure

compliance requirements, please follow operation instruction

as documented in this manual.
This transmitter must not be co-located or operating in con-

junction with any other antenna or transmitter.
The availability of some specific channels and/or operational

frequency bands are country dependent and are firmware pro-

grammed at the factory to match the intended destination. The

firmware setting is not accessible by the end user.

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be de-

termined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:
-  Reorient or relocate the receiving antenna.
-  Increase the separation between the equipment and receiver.
-  Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate this equipment. This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) This de-

vice may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause unde-

sired operation.

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pur-

suant to Laser Notice No. 50, dated June 24, 2007

Specific Absorption Rate (SAR) Information

The SAR Limit of USA (FCC) is 1.6W/kg averaged over one gram of tissue.

The device has been tested against this SAR limit. The highest SAR value

reported under this standard during product certification for properly

worn on the body is 0.75W/kg. This device was tested for typical body-worn

operations with the back of the Tablet PC kept 0 cm from the body. Any

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

1.4 Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003. Op-

eration is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that

may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Can-

ada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur

de l’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en compromettre

le fonctionnement.
Cet appareil numérique de la classe [B] est conforme à la

norme NMB-003 du Canada.

1.5 Battery Safety

Lithium-ion battery packs might get hot, explode, ignite and/or cause

serious injury if exploded by abusive using. Please follow the safety