Danfoss VLT, Programming Manual

Page: 32 / 231

0-20 Display Line 1.1 Small
Option: Function:
[1668] Pulse Input #33
[Hz] Actual value of the frequency applied
at terminal 33 as a pulse input.
[1669] Pulse Output #27
[Hz] Actual value of pulses applied to
terminal 27 in digital output mode.
[1670] Pulse Output #29
[Hz] Actual value of pulses applied to
terminal 29 in digital output mode.
[1671] Relay Output [bin] View the setting of all relays.
[1672] Counter A View the present value of Counter A.
[1673] Counter B View the present value of Counter B.
[1675] Analog In X30/11 Actual value of the signal on input
X30/11 (General Purpose I/O Card.
Option)
[1676] Analog In X30/12 Actual value of the signal on input
X30/12 (General Purpose I/O Card.
Optional)
[1677] Analog Out X30/8
[mA] Actual value at output X30/8
(General Purpose I/O Card. Optional)
Use
6-60 Terminal X30/8 Output to
select the variable to be shown.
[1680] Fieldbus CTW 1 Control word (CTW) received from
the Bus Master.
[1682] Fieldbus REF 1 Main reference value sent with
control word via the serial communi-
cations network e.g. from the BMS,
PLC or other master controller.
[1684] Comm. Option
STW Extended fieldbus communication
option status word.
[1685] FC Port CTW 1 Control word (CTW) received from
the Bus Master.
[1686] FC Port REF 1 Status word (STW) sent to the Bus
Master.
[1690] Alarm Word One or more alarms in a Hex code
(used for serial communications)
[1691] Alarm Word 2 One or more alarms in a Hex code
(used for serial communications)
[1692] Warning Word One or more warnings in a Hex code
(used for serial communications)
[1693] Warning Word 2 One or more warnings in a Hex code
(used for serial communications)
[1694] Ext. Status Word One or more status conditions in a
Hex code (used for serial communi-
cations)
[1695] Ext. Status Word 2 One or more status conditions in a
Hex code (used for serial communi-
cations)
[1696] Maintenance
Word The bits reflect the status for the
programmed Preventive
0-20 Display Line 1.1 Small
Option: Function:
Maintenance Events in parameter
group 23-1*
[1830] Analog Input
X42/1 Shows the value of the signal applied
to terminal X42/1 on the Analog I/O
card.
[1831] Analog Input
X42/3 Shows the value of the signal applied
to terminal X42/3 on the Analog I/O
card.
[1832] Analog Input
X42/5 Shows the value of the signal applied
to terminal X42/5 on the Analog I/O
card.
[1833] Analog Out X42/7
[V] Shows the value of the signal applied
to terminal X42/7 on the Analog I/O
card.
[1834] Analog Out X42/9
[V] Shows the value of the signal applied
to terminal X42/9 on the Analog I/O
card.
[1835] Analog Out
X42/11 [V] Shows the value of the signal applied
to terminal X42/11 on the Analog I/O
card.
[1836] Analog Input
X48/2 [mA]
[1837] Temp. Input X48/4
[1838] Temp. Input X48/7
[1839] Temp. Input
X48/10
[1850] Sensorless
Readout [unit]
[2117] Ext. 1 Reference
[Unit] The value of the reference for
extended Closed Loop Controller 1
[2118] Ext. 1 Feedback
[Unit] The value of the feedback signal for
extended Closed Loop Controller 1
[2119] Ext. 1 Output [%] The value of the output from
extended Closed Loop Controller 1
[2137] Ext. 2 Reference
[Unit] The value of the reference for
extended Closed Loop Controller 2
[2138] Ext. 2 Feedback
[Unit] The value of the feedback signal for
extended Closed Loop Controller 2
[2139] Ext. 2 Output [%] The value of the output from
extended Closed Loop Controller 2
[2157] Ext. 3 Reference
[Unit] The value of the reference for
extended Closed Loop Controller 3
[2158] Ext. 3 Feedback
[Unit] The value of the feedback signal for
extended Closed Loop Controller 3
[2159] Ext. 3 Output [%] The value of the output from
extended Closed Loop Controller 3
[2230] No-Flow Power The calculated No Flow Power for the
actual operating speed
Parameter Description
VLT
®
HVAC Drive Programming Guide
MG.11.CB.02 - VLT
®
is a registered Danfoss trademark 31
3 3