Danfoss VLT AQUA Drive FC 202, Design Manual, Page: 86 / 218

Type designation P45K P55K P75K P90K
Continuous at 575 V [A] 47 56 56 75 75 91 91 119
Intermittent at 575 V [A] 70 62 85 83 113 100 137 131
Maximum pre-fuses [A] 150 160 225 250
Additional specifications
Protection rating IP20 maximum cable cross-
section for mains and motor [mm
2
(AWG)]
50 (1) 150 (300 MCM)
Protection rating IP20 maximum cable cross-
section for brake and load sharing [mm
2
(AWG)]
50 (1) 95 (4/0)
Protection ratings IP21, IP55, IP66 maximum
cable cross-section for mains and motor
[mm
2
(AWG)]
50 (1) 150 (300 MCM)
Protection ratings IP21, IP55, IP66 maximum
cable cross-section for brake and load shar-
ing [mm
2
(AWG)]
50 (1) 95 (4/0)
Maximum cable cross-section
(2)
for mains dis-
connect [mm
2
(AWG)]
50, 35, 35 (1, 2, 2) 95, 70, 70 (3/0, 2/0, 2/0) 185, 150, 120 (350 MCM,
300 MCM, 4/0)
Estimated power loss
(3)
at rated maximum
load [W]
(4)
740 900 900 1100 1100 1500 1500 1800
Efficiency
(5)
0.98
1
High overload=150% or 160% torque for a duration of 60 s. Normal overload=110% torque for a duration of 60 s.
2
The 3 values for the maximum cable cross-section are for single core, flexible wire, and flexible wire with sleeve, respectively.
3
Applies for dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses may increase. LCP and
typical control card power consumptions are included. For more detailed efficiency values and part load losses according IEC/EN 61800-9-2 refer to
mydrive ecosmart on www. danfoss.com . For efficiency class see 8.4.1 Environment .
4
Efficiency measured at nominal current. For more detailed efficiency values and part load losses according IEC/EN 61800-9-2 refer to mydrive ecos-
mart on www. danfoss.com . For efficiency class see 8.4.1 Environment .
5
Measured using 5 m (16 ft) shielded motor cables at rated load and rated frequency. For more detailed efficiency values and part load losses ac-
cording IEC/EN 61800-9-2 refer to mydrive ecosmart on www. danfoss.com . For efficiency class see 8.4.1 Environment .
8.1.6 Mains Supply 3x525–690 V AC
Table 39: Enclosure, Mains Supply 3x525–690 V AC IP20/Protected Chassis, P1K1–P7K5
Type designation P1K1 P1K5 P2K2 P3K0 P4K0 P5K5 P7K5
High/normal overload
(1)
HO NO HO NO HO NO HO NO HO NO HO NO HO NO
Typical shaft output [kW] 1.1 1.5 2.2 3.0 4.0 5.5 7.5
Typical shaft output [hp] 1.5 2.0 3.0 4.0 5.0 7.5 10
IP20/Chassis A3 A3 A3 A3 A3 A3 A3
Output current
Continuous (3x525–550 V) [A] 2.1 2.7 3.9 4.9 6.1 9.0 11
Intermittent (3x525–550 V) [A] 3.2 2.3 4.1 3.0 5.9 4.3 7.4 5.4 9.2 6.7 13.5 9.9 16.5 12.1
Continuous (3x551–690 V) [A] 1.6 2.2 3.2 4.5 5.5 7.5 10
AJ300847815559en-000101 / 130R0337 86 | Danfoss A/S © 2020.09
Specifications
VLT® AQUA Drive FC 202
Design Guide