2-6
INSPECTIONS / ADJUSTMENTS
VALVE CLEARANCE
•
Remove the cylinder head cover.
•
Remove the A.C generator cap and crankcase hole cap.
•
Rotate the flywheel counterclockwise to align the "T"
mark with the index mark on the left crankcase cover.
•
Make sure the piston is at TDC(Top Dead Center) on
the compression stroke.
SHIM ADJUSTMENT
•
If the valve clearance is out of standard, adjust the shim
as below.
-
Remove the camshaft.
-
Remove the valve lifter and shim.
•
Remove the valve lifter and clean by compressed air.
•
Mop the oil from the attached area of shim, and
measure and record the thinkness with a micrometer.
•
Inspect and adjust valve clearance while the engine
is cold. (below 35
°
C/95
°
F)
•
If the valve lifter is to be removed, use the special
tool.
•
Be careful not to drop the shim into the cylinder
when remove the shim with valve lifter.
•
If it is too difficult to remove the shim, use a tweezer
or magnet.
•
Valve lifter, and shim should be preserved on the
assembly position distinguishably.
•
Measure the valve clearance with a feeler gauge.
VALVE CLEARANCE : INTAKE : 0.15mm
EXHAUST : 0.20mm
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
“T” MARK
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
FEELER GAUGE
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
VALVE LIFTER
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
CAM SHAFT
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
SHIM
Summary of Contents for Roadwin 250R FI VJF125
