D-Link DVG-5112S User Manual Download

Page: 73 / 98

DVG-5112S User’s Manual

MAINTENANCE

D-Link Systems, Inc.

3-3 MAINTENANCE

3-3-1 Device Management

MAINTENANCE

→

Device Management

Note:

There are two operating levels when entering the Web UI. Logging-in as the ADMIN allows you to

change all settings. A Web UI USER only has access to some settings.

Password:

By default there is no password configured. It is highly recommended that you create a

password to keep your VoIP Telephone Adapter secure.

MAINTENANCE

→

Device Management

Port of Web Access from WAN:

Enter the port number when accessing the web-based configuration

utility from the WAN port.

Web Idle Time Out:

Enter the range of effective time when log-in the web interface. The user will be

disconnected from the web page to allow others to log-in.

TFTP Source Port:

Enter the port number for sending out sends TFTP sessions.

Enable Web UI:

Check the box to enable WEB access from WAN or LAN.

Enable Telnet Service:

Check the box to enable Telnet access from WAN or LAN.

Summary of Contents for DVG-5112S



































































































Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands

D-Link DVG-5112S, User Manual

Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands