D-Link DVG-5112S User Manual Download

Page: 67 / 98

DVG-5112S User’s Manual

ADVANCED

D-Link Systems, Inc.

3-2-3-5 Virtual Server

Enable users on Internet to access the WWW, FTP and other services from your NAT. It is also known
as port forwarding. When remote users are accessing Web or FTP servers through WAN IP address, it
will be routed to the server with LAN IP address.

ADVANCED

→

Firewall and DMZ

→

Virtual Server

Enable Virtual Server:

Check the box to enable port forwarding.

WAN Port Range:

Enter the port range for the WAN side.

TCP/UDP:

Select the communication protocols used by the server,

TCP

UDP

Both

LAN Host IP Address:

Enter the IP address of the device that provides various services.

Server Port Range:

Enter comments.

Remark:

Enter comments.

Summary of Contents for DVG-5112S



































































































Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands

D-Link DVG-5112S, User Manual

Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands