D-Link DVG-5112S User Manual Download Page 68

Page: 68 / 98

DVG-5112S User’s Manual

ADVANCED

D-Link Systems, Inc.

3-2-4 Advanced Network

3-2-4-1 QOS

WAN QoS

ADVANCED

→

Advanced Network

→

QoS

Enable WAN QoS:

Check the box to guaranty the voice quality. The system reserves the bandwidth for

voice packets, and the data transmission is distributed to less bandwidth.

Downstream Bandwidth -

Select the downstream bandwidth that is less than the actual bandwidth

subscribed from the drop-down menu.

Upstream Bandwidth -

Select the upstream bandwidth that is less than the actual bandwidth

subscribed from the drop-down menu.

ToS IP Precedence:

Select the precedence for signaling (data) and voice (voice data) to tag voice

packets.

DiffServ (DSCP):

Select the number of signaling (data) and voice (voice data) values to tag voice

packets.

Note:

For the VoIP TA, ToS IP Precedence and DiffServ are the same function. You only select one for

priority marking.

Summary of Contents for DVG-5112S



































































































Search results

Summary of Contents for DVG-5112S

Reviews:

D-Link DVG-5112S, User Manual, Page: 68 / 98

Search results

Summary of Contents for DVG-5112S

Reviews: