D-Link DVG-5112S User Manual Download

Page: 34 / 98

DVG-5112S User’s Manual

ADVANCED

D-Link Systems, Inc.

3-2-1-3 Calling Features

ADVANCED

→

VoIP

→

Calling Features

Do Not Disturb:

Check the box to reject (busy tone played) incoming calls.

Unconditional Forward:

Check the box to forward incoming calls to the assigned “Forwarding

Number” automatically. If configured forwarding to FXO it only makes FXO hook off, but not making
FXO dial out.

Busy Forward:

Check the box to forward incoming calls to the “Forward incoming Number” when the

line is busy.

No Answer Forward:

Check the box to forward incoming calls to the “Forward incoming Number” after

ringing timeout (configurable from 10 to 60 seconds) expires.

Call Hold:

Check the box to hold the call on the specific FXS port.

Note: Call Transfer

Call Waiting

Three-Way Calling / Service ID

and

Local Mixer

can only be

activated when

Call Hold

is checked.

Call Transfer:

Check the box to transfer the call to another destination.

Call Waiting:

Check the box to accept incoming call while talking.

Three-Way Calling /Service ID:

It is for conference all based on Nortel Soft Switch and must work with

Proxy Server that supports Three-Way Calling service.

Local Mixer:

It is used to setup the conference call when your Proxy Server did not support Three-Way

Calling service.

Summary of Contents for DVG-5112S



































































































Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands

D-Link DVG-5112S, User Manual

Search results

Summary of Contents for DVG-5112S

Reviews:

Related manuals for DVG-5112S

Brands by name

Popular brands