D-Link DVG-5112S User Manual Download | Manualshive

Page: 32 / 98

background image

DVG-5112S User’s Manual

ADVANCED

D-Link Systems, Inc.

32

3-2 ADVANCED

3-2-1 VoIP

3-2-1-1 Caller Filter

This function allows you to accept or reject any incoming call from the IP address listed in the filter rule.
The call from the IP address of SIP proxy server is always accepted, despite Deny is selected or the IP
address of SIP proxy server is not in the filter rule of Allow.

ADVANCED

→

VoIP

→

Caller Filter

Caller Filter:

It is to allow or deny the filter rule.

Status:

It is to show the status of enable or disable.

Filter IP Address:

Enter the start IP address which you would like to Allow or Deny.

Subnet Mask:

Enter the subnet mask you would like to Allow or Deny.

«
...
30
31
32
33
34
...
»

Summary of Contents for DVG-5112S



































































































Reviews:

No comments

Related manuals for DVG-5112S

Brand: Keithley Pages: 73

Brand: Quantum Pages: 4

Brand: Quantum Pages: 2

Freedom SW 2000

Brand: Xantrex Pages: 36

CrossPower C4L5200-ETH

Brand: C4Line Pages: 26

Brand: Parker Pages: 36

Brand: König Electronic Pages: 25

Brand: National Instruments Pages: 27

Brand: NetComm Pages: 32

HandyPort HPU-120

Brand: HandyWave Pages: 19

Celerity FC-41ES

Brand: ATTO Technology Pages: 2

Brand: Parker Pages: 52

Brand: GodEngine Pages: 92

Brand: D-Link Pages: 2

DWA140 - RANGE BOOSTER N USB ADAPTOR

Brand: D-Link Pages: 58

Brand: D-Link Pages: 3

Brand: D-Link Pages: 3

Brand: D-Link Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands