manualshive.com logo in svg

D-Link DVG-5112S, User Manual, Page: 21 / 98

Share
Download
D-Link DVG-5112S User Manual Download Page 21

DVG-5112S User’s Manual 

 

                                                              SETUP

 

D-Link Systems, Inc.

                                                                                                                                                          21 

SETUP 

→

 Internet Setup 

 

 

Factory Default MAC Address:

 The original MAC address of the VoIP Telephone Adapter.   

Your MAC Address:

 It is left blank as you log-in via the WAN port. 

Current MAC Address:

 It shows the current MAC Address if you ever used the different MAC address 

from Factory Default MAC Address. You can click 

Clone

 to automatically copy the MAC address of the 

Ethernet Card installed in the computer used to configure the device. 

Note:

 This is only necessary to fill the field if required by your ISP. 

 

 

VLAN – This feature is only supported for the special hardware.

 

 

 

VLAN is optional. It works with the Router or Switch that supports VLAN tag. By adding VLAN tag in 
packets may improve efficiency of voice traffic performance and security. 

 

Enable VLAN Tagging:

 It is to tag the packets for VLAN Router or Switch identifying. 

VLAN ID:

 It is to assign uniquely a user-defined ID to each packet. 

Priority:

 It is the proprietary to VLAN Router or Switch. 

Note: Please do not change anything here unless requested by your ISP.

 

 
 

Summary of Contents for DVG-5112S



































































































Reviews:

No comments