Cisco PA-2JT2 Installation And Configuration Manual Download | Manualshive

Page: 1 / 28

background image

Corporate Headquarters:

Copyright © 1997–2002. Cisco Systems, Inc. All rights reserved.

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

PA-2JT2 6.3-MHz Serial Port Adapter Installation
and Configuration

Product Numbers: PA-2JT2 and PA-2JT2=

This configuration note describes how to install and configure the Japan T2 Line (JT2) 6.3-megahertz
(MHz), 2-port, serial port adapter (PA-2JT2[=]), which is used on the second-generation Versatile
Interface Processor (VIP2) in all Cisco 7500 series and in Cisco 7000 series routers using the 7000
Series Route Switch Processor (RSP7000) and 7000 Series Chassis Interface (RSP7000CI). (For
complete and specific compatibility requirements, refer to the section “

Software and Hardware

” on page 3.)

Use this configuration note in conjunction with the configuration note

Second-Generation Versatile Interface Processor (VIP2)

Installation and Configuration

Document Contents

This configuration note is organized into the following sections:

•

Related Documentation, page 2

•

JT2 Port Adapter Installation Prerequisites, page 3

•

What Is the JT2 Port Adapter?, page 7

•

VIP2 and the JT2 Port Adapter, page 12

•

Obtaining Documentation, page 24

•

Obtaining Technical Assistance, page 25

1
2
3
...
»

Summary of Contents for PA-2JT2





























Reviews:

No comments

Related manuals for PA-2JT2

I2C-RS232-Adapter

Brand: COPTONIX Pages: 15

LUXOMAT IR-RC-Adapter

Brand: B.E.G. Pages: 4

Brand: jablotron Pages: 2

Brand: Belkin Pages: 64

Brand: Cameo Pages: 19

Brand: IOGear Pages: 10

Brand: nedis Pages: 2

Brand: nedis Pages: 2

Brand: nedis Pages: 2

Brand: Philips Pages: 2

Brand: Cisco Pages: 217

Brand: D-Link Pages: 16

Brand: D-Link Pages: 3

Brand: D-Link Pages: 23

Brand: D-Link Pages: 2

dlinkgo GO-USB-N150

Brand: D-Link Pages: 40

Brand: D-Link Pages: 12

Brand: D-Link Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands